Inredning till EK/EJ

[Axzza]

Tja!

Lite saker jag funderar på för tillfället gällande min EJ9 -98:

Hur får man loss sittdelen av baksätet?
Kan man ta stolar + baksäte från en EP3 o sätta i min utan större problem?

Och generellt: Om man vill klä om dörrsidorna, vilket tyg/material bör man använda?

[Axzza]

Ingen som vet?
Funderar på om stolar + baksäte från en prelude -92 passar i min? Bara två säten bak o en mittkonsol på denna modell, tror ni det funkar?

[Andreas79]

DIY - 92-96 Prelude seat install in EK
Ok there is no good DIY on installing these bad boys in EKs, so I will make you one.
For starters this was kind of a bitch, you have to do some drilling and matching of notches in the rails.

Note - I will refer to outer rail a lot; this is the outer most rail of each seat. Ex: If you are sitting in the drivers seat looking down at your zipper, it is the rail to your left. Next to the door.
What you need:
- x2 - 8mm bolt <1" long w\ nuts
- Dremel really helps
- Metal drill bits (small one for piolet hole)
- 4hrs at most ( it took me this long because, I was stoned)

Step one:
Take out the civic seats and take the outer rails off the EK seats. Take a look at your floorboard; the outer side is what we are concerned with. Look at the rear bolt for the outer rail, you will see that it bends to a 90 degree bend. The prelude rail is flat, so we need to use the civic one that has that 90 degree bend to match the floorboard hole.

Step Two:
So take the outer rails off the prelude seats. Now if you hold the two up to each other they don't match, the civic ones are shorter. This effects the notches in the inside Lude rails, basically if you put the one screw that is attached to the Civic rail. These notches I am referring to are the notches that it locks into when you slide the seat back and forth. So the problem is, the civic rail will not go as far back as the Lude rail. So you need to drill a hole exactually 1" for the bolts for the EK rail. Starting with the bottom most holes on the seat. Measure 1” up and the hole is actually 1\4” off the right edge of the seat, they are NOT in the center. Now for the rear hole, after you drill the first hole you will see that the 2nd hole is going to be right on top of this silver aluminum bracket where the plastic molding screwed into. This is in the way, and prevents you from getting the screw (refer to step three) in the hole. So you say to your self, wtf is this guy thinking?! Well this bracket with the hole for the screw isn't important, you only need 1/4 of the holeÂ’s threads to screw in the screw to mount the plastic molding, TRUST ME! So you can either use your drill bit to mill down the bracket going through the hole, or use a Dremel and cut the bitch down. Make sure you leave ~ 1/4” of thread so you have something to screw that screw into. I know this seems getto, but it works and it is not any of its structural integrity. TRUST ME!

Step Three:
Go to the hardware store and get two 8mm bolts that are < 1”, any longer than this and it will hit the rail when it slides all the way back. If you run into this problem, just cut off the bolt above the nut like I had to do.

Step Four:
Those bolts you got are for the rear hole on the rail; reuse the nut from taking off the prelude rail for the attached bolt on the front. I had to cut off the top of the rear bolt so it would clear the rail when going all the way back. Use a Dremel.

Step Five:
Measure Measure Measure, you got to be sure that the notches on the Lude rail matches the notches on the EK rail. Also make sure the rails are straight when they are mounted on the seat!!! An easy ways is to run your finger down the outer side and feel for any shifts.

Step Six: Installing
Now the EK outer rails match up perfectly, but in my first attempt the inner didn't. Match up the hole for the inner rear bolt, the front wonÂ’t fit so just make sure you cut the carpet around it and hammer it flush with the floorboard. So you have three bolts that match up into the factory holes, it will take a little effort to get that inner rear bolt in but it will go. Just make sure that you are pushing on the seat the entire time you are screwing in the bolt to avoid any intense pressure on the bolt.
Now the inner front is a different story, you can drill a hole in the bracket which I donÂ’t recommend doing. Altering the integrity of the bracket is no good in my book. So at the auto store get some rubber grommets that fit in the factory holes in the floor board to plug them up to prevent any water or something like that. Then drill a hole for the brackeÂ’s hole in the floorboard; you will need a thick bolt with deep thread. So that it will grip into the floorboard, you basically want a short thick bolt with deep threads for sheet metal.
Now I know you are thinking to your self, "I don't want to drill into the floor board." but it's the sturdiest way to do it. Bottom line

Källa: http://honda-tech.com/showthread.php?t=766603

[Andreas79]

EP3: "Custom bracket are a must and they sit to high there better off in an eg or em"

Depends how you align it 1 or 2 bolts would line up with aid of a rubber mallet hitting
down on the rails. The rears i used galivinized bolts and drilled through the floor boards.
I used the stock ep3 rails..

but its better and will align better if you use your ej8 or ek rails on the ep3 seats.
the ep3 seat bucket (square thing under the seat that the rails are bolted to) is tack welded on...you would need to break through those welds...

Källa: http://www.clubcivic.com/board/showthread.php?t=124286

[Andreas79]

Angående klädsel i dörrarna vid elhiss-knapparna har jag alcantara tyg i
min bil iallafall, en del pill med det.

Köpt för några år sedan Stoff och stil i Malmö, Svågertorp
http://www.stoffochstil.se/

[Andreas79]

Bilder demontering av gamla baksätet och recarobaksätet:
http://www.garaget.org/mypage/gallery.p ... lbum=27601

Angående baksäte - att ta ur det är där några fästen under själva sitsen, man känner
direkt var de finns undertill, kan sitta rejält hårt men bara att testa,
på flera ställen av själva sitsen alltså, framifrån och bakifrån på sistsen finns
fästena:



Själva ryggen till baksätet kan sitta fast ordentligt i sidorna med annat typ
av fäste, med bultar av något slag..

[Axzza]

Tackar jättemycket för infon Andreas!

Mer info kommer i projekttråden!

[Andreas79]

Tackar jättemycket för infon Andreas!

Mer info kommer i projekttråden!

Varsågod = )